Tips On How To Extend Smok Pen Recharge Time
The Smok Pen is a new pen that was developed by two guys in California. They wanted to create a cool writing instrument that looked like a real pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the marketplace by storm.
The Smok Pen has a built quality that is just great. I came across that even though it can be an electronic pen the build quality is simply as good as the pens that I’ve reviewed. For the reason that of how they made the very best cap. You don’t need to be worried about the cap cracking or breaking you Smok Valve Pen.
The two biggest differences that separate the Smok Valve from other pens may be the shape of the coils and just how that they are built. In general the coil on a Smok Pen is larger than on other pens. I think that they did this on purpose, to make the pen feel more substantial.
Invest the a look at a Smok Pen, you will observe that your body of the pen is round and not smooth like other pens. On the trunk of the pen there is a little tab that houses the coil. Once you press on the tab it is simple to turn the heating element on and off. I must say i liked this feature since it allows me to utilize the Smok Pen 22 whenever I feel like smoking.
To utilize the Smok Pen it is advisable to keep carefully the heat button pressed. Once the button is pressed, the heating element will start to warm up. Once it reaches the appropriate temperature you can switch off the heating element. Smok recommends using a 22mm tank. I prefer a larger tank, but that’s just me.
When you put your Smok Pen in to the tank you will see a indicator light come on. The indicator light will remain green if you don’t put your Smok Pen in to the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen into the charger before you apply the e-liquids to the coil heads. Additionally it is important to do that before putting your e-liquids into the coil heads.
Once you have completed this step, it is best to check to see when you are at the right temperature for the coils to fire. If not then you should turn the power off and try again. For anyone who is still not satisfied with your Smok Pen then I suggest you take it in for some troubleshooting. This is exactly what I’d call the “troubleshooting process” because sometimes things just do not work as they should. I suggest that you perform the following two steps, then go ahead and check the Smok Pen to see if it still gets the electronic charging port.
Prior to going any further you should take away the battery from your pen and unscrew the magnetic cap. You need to then remove the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body which is green in color. You need to loosen this wire using pliers. Once you have loosened this wire you can then access the sub-ohm. You should then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful never to touch any of the coils.
Once you have placed the sub-ohm tank into the pen you should then place the rest of the components including the wattage, the batteries and the heating element into the included microwaveable microwave oven. Start the power and follow the on screen instructions. You should place the pen’s battery in to the microwave and activate the setting. You should then wait approximately 30 seconds before turning it cool off. When you first put the pen in to the microwave the electronic reading will show a low voltage protection setting. If this setting does not automatically get set you then should follow the on screen instructions.
After the Smok Pen has reached the temperature that it requires to reach you should then connect both wires to the positive and negative on the positive post on the Smok unit. You should then connect another end of the battery to the negative post on the negative side of the Smok unit. The ultimate step is to connect the positive cable to the bottom of the Smok’s power switch.
After all the components have been placed into the pen, you should turn the podsmall.com energy on. After the first test run, you ought to be able to start to see the battery life indicator light seriously. If you don’t see any sign of life from the Smok Pen, you should take away the battery from the pen and then replace it with a fresh one. For your convenience there is also a green light which can be pressed as a way to confirm the battery charging status. If you have done these things and you also do not start to see the green light indicating charging, you should replace the battery.